2018 Nissan Rogue Oil Filter Number

Nissan
2018 Nissan Rogue Oil Filter Number

Okay, so you're looking for the correct oil filter for your 2018 Nissan Rogue. You've come to the right place! Finding the right filter is crucial for maintaining your engine's health and ensuring its longevity. Using the wrong filter can lead to all sorts of problems, from reduced oil pressure to premature engine wear. Let's break down how to identify the correct filter and address any potential issues you might be facing.

Identifying the Correct Oil Filter

The 2018 Nissan Rogue primarily uses one oil filter, but it's always a good idea to double-check based on your engine type and specific model. Here’s what you need to know:

The Standard Oil Filter

For the vast majority of 2018 Nissan Rogues with the 2.5L 4-cylinder engine (engine code QR25DE), the standard oil filter is:

Nissan Part Number: 15208-9F60A or 15208-31U0B

You'll often find aftermarket equivalents from reputable brands like:

  • Fram: PH7317
  • Purolator: L14610
  • Mobil 1: M1-110
  • K&N: HP-1002
  • Bosch: 3300

Always cross-reference the aftermarket part number with your vehicle's information before purchasing. This is easily done on the parts retailer's website or by speaking with a parts specialist.

Why is the Right Filter Important?

Using the correct oil filter is vital for several reasons:

  • Proper Fit: The correct filter will thread onto the oil filter housing correctly, preventing leaks.
  • Optimal Oil Flow: The filter's design allows for the correct oil flow rate, ensuring adequate lubrication throughout the engine.
  • Filtration Efficiency: A quality filter effectively removes contaminants, preventing engine wear.
  • Bypass Valve: Many filters have a bypass valve that opens if the filter becomes clogged, ensuring oil flow even when the filter is restricted. The correct filter will have a bypass valve set at the correct pressure for your engine.

Common Problems and Solutions

Let's address some common problems you might encounter when dealing with your 2018 Nissan Rogue's oil filter:

Problem: Difficulty Removing the Old Oil Filter

Sometimes, the old oil filter can be incredibly difficult to remove. This is often due to overtightening by the previous installer or simply the filter being stuck over time.

Solution:

  1. Oil Filter Wrench: Use a dedicated oil filter wrench. There are several types:
    • Cap-type wrenches: These fit over the end of the filter. Make sure you get the right size for your specific filter.
    • Band-type wrenches: These wrap around the filter and tighten as you apply pressure.
    • Pliers-style wrenches: These are adjustable pliers specifically designed for oil filters.
  2. Penetrating Oil: Spray some penetrating oil (like PB Blaster or Liquid Wrench) around the base of the filter where it meets the engine block. Let it sit for 10-15 minutes to help loosen the seal.
  3. Hammer and Screwdriver (Last Resort): If all else fails, carefully puncture the filter with a screwdriver and use it for leverage to turn the filter. Be extremely cautious not to damage the engine block. This method is messy!
  4. Heat (Carefully): Applying a little heat to the filter housing (not the filter itself!) with a heat gun can sometimes help expand the metal and loosen the filter. Be extremely careful and avoid overheating anything.

Tools Needed: Oil filter wrench (cap-type, band-type, or pliers-style), penetrating oil, screwdriver (if necessary), hammer (if necessary), heat gun (optional).

Problem: Leaking Oil Filter After Installation

A leaking oil filter is a serious issue that needs to be addressed immediately. Common causes include:

Solution:

  1. Loose Filter: The most common cause is simply not tightening the filter enough. Make sure the filter is hand-tightened, then tightened an additional ¾ to a full turn, as specified on the filter.
  2. Damaged O-Ring: The rubber O-ring on the filter might be damaged or improperly seated.
    • Before installing the new filter, always inspect the O-ring for any cracks or damage.
    • Lightly lubricate the O-ring with fresh engine oil before installation. This helps it seat properly.
  3. Double Gasket: Sometimes, the old O-ring from the previous filter can stick to the engine block. This creates a double gasket situation, leading to leaks. Make absolutely sure the old gasket is removed before installing the new filter.
  4. Damaged Threads: The threads on the filter or the engine block might be damaged. If this is the case, you might need to have the threads repaired or replaced by a professional.
  5. Incorrect Filter: Double-check that you are using the correct oil filter for your 2018 Nissan Rogue.

Tools Needed: Oil filter wrench, shop towels, fresh engine oil.

Problem: Difficulty Finding the Oil Filter Location

The oil filter location on the 2018 Nissan Rogue is relatively straightforward, but it can be tricky to spot at first glance.

Solution:

The oil filter is typically located on the front of the engine, near the bottom, usually accessible from underneath the vehicle. You will likely need to remove an access panel (if equipped) to get to it. Look for a cylindrical object that screws into the engine block.

Tips:

  • Refer to your owner's manual for a diagram showing the oil filter location.
  • Watch a YouTube video specifically showing an oil change on a 2018 Nissan Rogue.
  • Use a flashlight to get a better view of the engine bay.

Problem: Messy Oil Changes

Oil changes can be messy, but with a few precautions, you can minimize the mess.

Solution:

  1. Prepare Your Area: Cover the ground with a drop cloth or cardboard to catch any spills.
  2. Warm Engine: Warm the engine slightly before draining the oil. Warm oil flows more easily. However, be careful not to burn yourself on hot engine components.
  3. Proper Drain Pan: Use a drain pan that is large enough to hold all of the used oil.
  4. Pre-Soak the New Filter: Before installing the new filter, pre-soak it with fresh oil. This will help to prime the filter and reduce engine wear on startup.
  5. Clean Up Immediately: Clean up any spills immediately with shop towels or rags.

Tools Needed: Drop cloth, drain pan, shop towels, funnel.

Approximate Repair Costs

If you're not comfortable changing the oil yourself, you can take your 2018 Nissan Rogue to a mechanic. Here's an approximate breakdown of the costs:

  • DIY Oil Change: $30-$70 (depending on the cost of oil and filter). This assumes you have the necessary tools.
  • Oil Change at a Quick Lube: $50-$100 (using conventional or synthetic blend oil).
  • Oil Change at a Dealership or Independent Mechanic: $80-$150+ (especially if using full synthetic oil).

These are just estimates, and the actual cost may vary depending on your location and the type of oil and filter used. Dealerships tend to be more expensive due to higher labor rates.

Important Note: When getting an oil change, always ask for the specific type of oil and filter being used. Also, check your owner's manual for the recommended oil type and viscosity for your 2018 Nissan Rogue.

By understanding the correct oil filter for your 2018 Nissan Rogue and addressing potential problems proactively, you can keep your engine running smoothly for years to come. Remember to always consult your owner's manual and seek professional advice if you're unsure about any aspect of the oil change process. Good luck!

Related Posts